Humminbird 531655-1_A Manuel d'utilisateur télécharger pdf

1100 Series™ In-Dash Mounting Kit

531655-1_A

Thank You

Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its

reputation by designing and manufacturing top-quality, thoroughly reliable marine equipment.

Genuine Humminbird® accessories offer the opportunity to upgrade and expand the capabilities

of your Humminbird® product.

Your Humminbird® is designed for trouble-free use in even the harshest marine environment. In

the unlikely event that your Humminbird® does require repairs, we offer an exclusive Service

Policy - free of charge during the first year after purchase, and available at a reasonable rate after

the one-year period. For complete details, see the Warranty section included in this manual.

Contact our Customer Resource Center at either 1-800-633-1468 or visit our website at

www.humminbird.com.

Installation Overview

Following are instructions for the installation of this accessory. Before you start installation, we

encourage you to read these instructions carefully in order to get the full benefit from your

Humminbird® accessory.

If you find that any items are missing from your installation kit, call our Customer Resource Center

at 1-800-633-1468 or visit our website at www.humminbird.com.

Installation

Start by placing the components on the surfaces where you intend to install them before

installation. Make sure that the surfaces you have chosen provide adequate protection from

wave shock, and that all cables can reach the control head.

NOTE: If a cable is too short for your application, extension cables are available.

Call Humminbird® Customer Support at 1-800-633-1468 for more information.

Parts and tools specific to In-dash mounting are:

• Threaded rods and hardware

• In-dash mounting foam pads

• In-dash mounting template

• Reciprocating saw for cutting dash material

• Masking tape to hold mounting template in place.

1. Locate a suitable, flat area of the dash to mount the control head. The control head

requires a depth of at least 4 inches (102 mm).

2. Tape the paper In-Dash Mounting template to the desired in-dash mounting location.

3. At a location inside the dotted line on the template, drill a hole large enough to insert

blade of reciprocating saw. In addition, drill the 4 mounting hole locations using a 3/16"

drill bit. Carefully begin cutting toward the dotted line, then follow the dotted line

around the template. Remove the template when finished.

4. Insert and tighten the four threaded rods into the four threaded inserts located on the

back side of the control head. Peel off the adhesive-backed foam pads and place them

on the back of the control head; make sure you notice the difference between the

longer top/bottom and shorter side pads.

Threaded Rod

Washer

Wing Nut

Lock Washer

Cut

Away

Dash

Foam Pads

Mounting the Control Head

1 2 3 4

Résumé du contenu

Page 1 - Installation

1100 Series™ In-Dash Mounting Kit1531655-1_AThank YouThank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built

1100 Series™ In-Dash Mounting Kit2531655-1_A5. Insert the control head through the mounting hole from the front side of the dash.Place a washer, lock

Page 3 - Humminbird® Service Policy

1100 Series™ In-Dash Mounting Kit3531655-1_A1-Year Limited WarrantyWe warrant the original retail purchaser that products made byHumminbird® have been

Page 4 - Contact Humminbird®

1100 Series™ In-Dash Mounting Kit4531655-1_AReturning Your Unit for ServiceBefore sending your unit in for repair, please contact the factory, eitherb

Commentaires sur ces manuels

Pas de commentaire

Humminbird 531655-1_A Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Non Humminbird 531655-1_A. Humminbird 531655-1_A User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non Humminbird 531655-1_A