Humminbird ProAngler Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Sports et loisirs Humminbird ProAngler. Humminbird ProAngler User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 33
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Vue de la page 0
1 2 3 4 5 6 ... 32 33

Résumé du contenu

Page 2 - INSTALLATION PREPARATION

mounting bracket. Drill this hole and install the screw after final testing and adjustments have been completed.

Page 3

INSTALLATION TRANSOM INSTALLATION Step Six - Route the Cable There are several ways to route the transducer cable to the to the area where the contr

Page 4

INSTALLATION INSIDE THE HULL INSTALLATION INSIDE THE HULL INSTALLATION Inside the hull installation requires the mount system and control head be in

Page 5

The transducer cannot transmit through air. The water purges any air from between the transducer and the hull and fills any voids in the coarse fiber

Page 6

INSTALLATION INSIDE THE HULL INSTALLATION 3. Power up the Control Head. 4. Run the boat at various speeds and water depths while observing the scr

Page 7

INSTALLATION CONTROL HEAD INSTALLATION CONTROL HEAD INSTALLATION Step One - Determine Where to Mount Begin the installation by determining where to

Page 8

fuse in the connection. If you must wire the control head directly to a battery, be sure to install an inline fuse holder

Page 9

INSTALLATION CONTROL HEAD INSTALLATION and one amp fuse (not included) for the protection of the unit (Figure 21). Humminbird is not responsible for

Page 10

Optional: If the cables pass outside the mounting bracket, install the hole cover over the hole and fasten in place using the two #8 x 7/8” (22mm) woo

Page 11 - INSTALLATION

INSTALLATION CONTROL HEAD INSTALLATION Step Five - Assembling the Connector Holder 1. Insert the cable connectors into the connector holder. The ca

Page 12

INSTALLATION PREPARATION PARTS SUPPLIED PARTS SUPPLIED Before installing your new Humminbird fishfinder, please ensure the following parts are inclu

Page 13

INSTALLATION TEST THE INSTALLATION TEST THE INSTALLATION Testing should be performed with the boat in the water, however you can initially confirm b

Page 14

AVAILABLE ACCESSORIES Humminbird offers a wide assortment of accessories which complement and expand the capability of your new ProAngler. These acce

Page 15

The range of the graphic display is shown to the right of the graphic information. The upper number is 0 indicating the surface of the water, the lowe

Page 16

Sonar targets which are not physically attached to the bottom may take one of many shapes. Surface clutter is the layer of water near the surface whic

Page 17

CONTROL FUNCTIONS The ProAngler uses a simple 5-button keypad for all user input. When any button is pressed, an audible "chirp" confirms t

Page 18

options, press and hold MENU-the menu will remain on-screen indefinitely. Once you release the menu button, the screen will time out. Once a menu tim

Page 19

Menu Functions The Sensitivity function controls the sensitivity of the sonar receiver. The ProAngler automatically adjusts the level of receiver sen

Page 20

water, the 0-30' range would be selected). This provides the best display resolution and therefore the best target separation possible. The Dept

Page 21

shown on the right side of the display. Zoom can either operate automatically, in which the Zoom range is constantly adjusted to show the bottom, or m

Page 22

Depth Alarm The ProAngler contains an audible alarm to warn you of shallow water depths. The alarm is adjustable from 2' to 99' of depth.

Page 23

INSTALLATION PREPARATION INSTALLATION OVERVIEW Determining How to Mount the Transducer Your Humminbird fishfinder includes a standard transducer. Th

Page 24

To disable the Fish Alarm, press MENU until the Fish Alarm menu appears onscreen. Use the UP ARROW to highlight "Off", and let the menu ti

Page 25

Press MENU until the Options menu is on-screen. There are two choices, Hide (Factory Setting) and Show. Use the DOWN ARROW to highlight Show and the f

Page 26

Bottom Black The next Option menu is Bottom Black. There are two selections available; Off and On. The factory setting is Off. With this setting, the

Page 27

service. In conjunction with the failed indication will be a code which indicates to the repair personnel where the problem is.

Page 28

INSTALLATION PREPARATION ALTERNATE MOUNTING METHODS ALTERNATE TRANSDUCERS AND MOUNTING METHODS Your Humminbird fishfinder comes with everything nece

Page 29

INSTALLATION PREPARATION TRANSDUCER EXCHANGE TRANSDUCER EXCHANGE Other transducers are available as replacements for the standard transducer. You ma

Page 30

INSTALLATION TRANSOM INSTALLATION Do not begin this transducer installation until you read the Installation Preparation in the Operation Guide. This

Page 31

INSTALLATION TRANSOM INSTALLATION • If the propeller(s) is (are) forward of the transom, it may be impossible to find an area clear from turbulence,

Page 33

INSTALLATION TRANSOM INSTALLATION Step Four - Mount the Transducer to the Transom 1. Apply silicone sealant to the mounting holes drilled into the

Commentaires sur ces manuels

Pas de commentaire